Enclosed matching trailer optional
High Compression motor (rebuilt July, 2013) with 50 hours
New rod bearings
Inspected rings, cleaned and reinstalled
Crank spec'd to...
Enclosed matching trailer optional
High Compression motor (rebuilt July, 2013) with 50 hours
New rod bearings
Inspected rings, cleaned and reinstalled
Crank spec'd to standard and polished
Lindsey oil pan baffle installed
Head cleaned, valves removed and cleaned. Hand-lapped and new seals installed
Full engine seals, every seal replaced front to back, top to bottom
Heater line blocked on head and at water pump. Lines deleted to heater core.
New water pump
Kevlar timing belt and new stock balance belt.
Late cam installed in powder coated cam box
Idle valve deleted and silicone hose from AOS to J-boot installed
All silicone vacuum hoses
Paurman braided fuel lines and fuel pressure gauge with remote braided line
New distributor cap and rotor
Lindsey Firebraid spark plug wires, new Bosch plugs
A/C delete bracket and belt installed
Amsoil 20w50 Dominator Synthetic Oil.
All radiator hoses replaced new at rebuild. Turbo radiator installed.
Aftermarket oil cooler with AN10 fittings routed to factory turbo/s2 engine plate with adapters welded on for AN10 at the engine. * Factor oil sender removed and adapter in place for manual oil pressure gauge
Late header with modified stock exhaust. Cat deleted
Trans replaced with a tight factory late LSD trans.
New axles installed in August, 2014 (preventive maintenance)
Clutch new at rebuild. New pressure plate, aftermarket clutch and new throwout bearing.
Newer clutch hydraulics from turbo with NEW clutch line.
Epoxy coated a-arms and rear trailing arms. New bearings front and rear.
New front rotors installed at rebuild.
Hawk DTC-60s pads front/ HP+ rears
Braided Stainless Steel brake lines with Super Blue fluid always used
All calipers removed, sandblasted, new seals installed and painted- new rubber caps on bleeders as well.
Koni Yellow struts with new-er adjustable inserts
New Koni rear sport shocks at build
Installed adjustable Weltmeister front and rear sway bars (~$800) in 2014 (6 hours on them)
350 lb front Hypercoil coils with adjustable sleeves
Ground Control camber plates
Turbo brake shield scoop[s at back of front rotors
968 castor blocks- welt, poly front a-arm bushings and rear torsion bushings.
Car was aligned and corner balanced in Aug. 2014. Only 1 race since completed
Braille battery for the car- 6 lb installed
Car weighed in at 2615 at last weigh in with very little gas and 180 lb driver
Suspension set at 3.5 neg camber front- 2.5 rear. No toe front/ slight toe in rear. Max castor front.
Hanksville Hotrods cage installed with optional Nascar drivers door bar and knee bar. $1,700 shipped. Painted with epoxy grey to hold up to use and abuse.
All padding is good impact padding on drivers side and some on PS from when there was a passenger seat
Engine DME computer is mounted to passenger kick panel area out of the way but accessible.
Autometer Oil pressure and Temp gauges in dash
Fire suppression system installed; 3 nozzles. One in cabin faces driver. Two under hood- one on each side of the motor. Pull is located in center of the dash next to toggle switches. Needs a bottle.
Emergency battery disconnect is mounted on the drivers side a-pillar and kills neg. Battery terminal as well as the coil wire to the car.
Three switches on the dashboard; Cool Suit, lights, wipers/blower
Factory wiring to taillights is tied into the switched power in the dash. Rear running lights are on when car is on. Switch to lights only works headlights which are removed but all pieces are included with car. Wiring is still at the headlight buckets and custom brackets are installed to flip the headlights up or down for night driving.
Wipers work on a 2-way switch; fast/slow.
All HVAC is removed, but blowers in cowl are still installed. One side blowing down onto the drivers feet and other side is ducted to a vent in the top of the dash that can be used as defrost if needed
CARHAS A HARDWIREDTRANSPONDER.
Drivers window net is a OGRacing net that attaches at the top with a bar and buckle, bottom has straps that hang down and attach to the Nascar bar (top bar)
Center net is attached around the back of the drivers seat per instructions and goes through the dashboard and attaches to the knee bar which is up behind the dash.
Seat is a Sparco Evo. G-Force six point harness new at build. Needs to have new webbing installed per NASA regulations (Time limit expired)
Seat is mounted to steel side mounts that are welded to floor adapter plates (not moving). Mounts can be drilled to move the seat for any driver who needs adjusted
Steering lock is disabled
Steering wheel is a Momo Prototipo on a removable hub
Wide angle rear view mirror mounted to rollcage
TraqMate Data Acquisition System ($800) added/installed in 2014
New Cool Suit System added
New Hans Race Seat added/installed in Mar. 2014 ($1,500)
Three sets of 15x7 factory “phone dial” wheels; two red sets for dry and one set rains.
Vehicle Specs
Basic
Year
1987
Make
Porsche
Model
944 Spec Car
Engine
Engine Size
High Compression
Engine Type
Gasoline
Transmission Type
Manual
Body
Body Color
White
Body Style
Other
Doors
2
Interior
Seating Type
Racing Bucket Seats
Dealership Info
R&H Motor Car Group
R&H Motor Car Group is a company that turns out show winning exotic, custom, muscle, and vintage cars to our customer’s specifications. We pride ourselves on not only what we can find for you, but what we can fabricate, restore and finish.